Whether it’s legally required at your specific address is genuinely the less important half of this question. Here’s the real answer — the local legal picture, where risk actually comes from, where to put a detector, and what to do the moment one goes off.
Is It Actually Required, and Does Wood vs. Gas Change the Risk?
Missouri genuinely has no statewide CO detector mandate — one of a small handful of states, alongside Kansas, Indiana, and Hawaii, without one, because Missouri doesn’t have a statewide building code at all. What I actually tell people: check your specific city or county, don’t assume the absence of a state law means there’s no local one. Some cities and counties layer their own ordinances on top, the same local-code variation we’ve flagged repeatedly throughout this series — I’m not going to pretend I know every municipality’s ordinance, so the honest answer is always to check with your own local building or fire department.
Setting the legal question aside, I recommend one regardless of whether your address happens to require it. Missouri’s own Department of Public Safety, even without a legal mandate behind it, recommends CO detectors on every level of the home and centrally located near sleeping areas. “Not legally required” and “not worth having” are two completely different claims.
Does the real risk actually differ between wood and gas? Genuinely, no, not in overall severity, though the mechanism differs enough to be worth understanding both. Wood-burning risk tends to trace back to blockage and venting failure — a spalled or cracked liner letting flue gas migrate where it shouldn’t, debris obstructing the flue, chimney fire aftermath compromising a once-sound path. Gas risk tends to trace back to the combustion and safety-device side — a cracked heat exchanger, a degraded ODS on a vent-free unit, a blocked vent termination. Different mechanisms, comparably real danger either way.
The Family Who Thought Gas Meant They’d Left CO Risk Behind
A family who’d converted their older wood-burning fireplace to a vent-free gas log set told me directly that part of their reasoning had been wanting something they considered inherently safer than dealing with creosote and smoke — genuinely believing CO risk was something they’d left behind along with the firewood. They’d installed a CO detector anyway, which turned out to matter enormously, because it did eventually alarm — not from anything resembling their old wood-related concerns, but from the gas system itself, tracing back to an ODS and room-ventilation issue.
Nothing about their situation was unusual or negligent — it was a genuine example of CO risk simply changing shape rather than disappearing when they switched fuel types. Missouri’s lack of a state mandate doesn’t settle the question for your specific address — check locally. Don’t assume switching from wood to gas, or vice versa, changes your overall CO risk level — it changes the specific things worth watching for, not whether the risk exists at all.
Where to Actually Put It
Roughly 10 to 15 feet from the appliance, sometimes cited up to 20, but never directly above or beside it. A fireplace or wood stove genuinely releases trace amounts of CO during normal startup and operation, and a detector mounted too close, especially directly above a mantel, will trip on completely normal operation rather than a real problem. The “install close” and “stay back” advice you might find online aren’t really opposing camps — they’re both describing the same general room, real distance away, never right on top of it.
Height genuinely doesn’t matter much, which surprises people expecting the same logic as smoke detectors. Unlike smoke, which rises, carbon monoxide mixes fairly evenly with room air. A wall-mounted unit at roughly eye level is a completely reasonable default, more about convenience for testing and battery access than any real detection advantage. The baseline is one detector per level of the home, including the basement, plus one within about 10 feet of every separate sleeping area. On top of that, a living room or den containing a fireplace or wood stove genuinely deserves its own detector even if the level’s main unit is technically nearby, since that’s where people spend real waking hours around an active combustion source.
The Detector That Got Disabled by Its Own Placement
A homeowner had mounted a CO detector directly above the mantel of their wood stove, wanting it as close to the source as possible, reasoning closer meant safer. Every single time they lit a fire, normal startup emissions tripped it — essentially every use. Weeks of that wore them down, and they pulled the battery, meaning to move it eventually, which never happened. The real danger wasn’t the nuisance alarms themselves — it was what those alarms trained them to do. Months later, that stove developed a genuine venting issue, and there was no working detector left in the room to catch it.
Same room is fine and often the right call — right on top of the appliance is the actual mistake. If you’re getting frequent nuisance trips, that’s a placement problem to fix by moving it, not a reason to disable it. A detector disabled because of poor placement offers exactly the same protection as no detector at all — worse, really, since it creates false confidence that coverage exists.
What to Do the Moment It Goes Off
This isn’t a “figure out what’s wrong first” situation, it’s an “everyone out first” situation. Get everyone, including pets, out to fresh air immediately. Don’t stop to investigate the stove, don’t try to air the house out yourself. Once safely out, call 911 or your fire department from outside, and don’t go back in until responders tell you it’s safe. Any symptoms — headache, dizziness, nausea, confusion — are a medical emergency in their own right.
A properly functioning, correctly placed alarm has a genuinely different alert pattern for actual detection than for a low battery or end-of-life warning — commonly four chirps in a row followed by a pause for a real detection, versus a single chirp every 30 to 60 seconds for a battery or aging-unit issue. If placement is confirmed correct and you’re getting the distinct detection pattern, that’s not ambiguous — evacuate first and let professionals confirm afterward.
Most CO detectors have a real sensor lifespan of about 5 to 7 years, some rated up to 10, and that clock starts from the manufacture date printed on the unit, not from whenever you installed it. A detector can respond to its test button and still have a sensor degraded well past reliable — the test button generally checks the alarm circuit, not the sensor’s actual accuracy. An end-of-life chirp is a genuinely different pattern than a low-battery chirp, and swapping the battery does nothing to stop it. Flip the unit over and check the printed manufacture date directly.
The Family Who Left Immediately
A family was burning a normal evening fire when their CO detector went off with the genuine detection pattern. They didn’t pause to investigate — everyone, including their dog, was outside within a minute or two, and they called from the driveway. It turned out to be a real, developing blockage partially restricting their flue. Because they left immediately rather than spending extra minutes trying to figure it out themselves, nobody was exposed long enough to develop symptoms. Evacuate first, every time, before trying to identify the source yourself. Learn your specific detector’s real detection pattern versus its maintenance chirps.
What to Actually Buy
My honest recommendation leans toward a sealed 10-year battery unit for most households. Battery-only units are cheapest and most flexible to place, but put the entire ongoing reliability question on someone remembering to swap batteries. Hardwired units with battery backup are excellent, especially interconnected systems where one alarm triggers every unit in the house. A sealed, non-replaceable 10-year battery unit splits the difference — no battery swap to forget, and it sidesteps the end-of-life-versus-low-battery confusion, since there’s only one thing to eventually replace: the whole unit.
I lean standalone for the room with your fireplace specifically. A combination smoke/CO unit needs to carry certification to both UL 217 for smoke and UL 2034 for CO, not just one — a bargain combo unit can technically be a legitimate smoke detector while skimping on the CO sensing half. Wall-mounted gives you real control over correct placement; a plug-in unit only goes where an outlet already exists, and if that outlet sits closer to your fireplace than the 10-to-15-foot minimum, convenience can quietly override correct placement. Look for electrochemical sensor technology, the modern standard for accuracy and stability.
Real cost: a basic standalone battery-only unit typically runs $15–$30. A sealed 10-year battery standalone unit, $25–$45. A properly dual-certified combo smoke/CO unit, $30–$60. A hardwired, interconnected system, $40–$70 per unit before electrician labor. The jump from bargain to reliable isn’t dramatic in absolute dollars.
The Combo Unit That Trained Her to Ignore Alarms
A homeowner bought a plug-in combo unit for simplicity and plugged it into the nearest outlet, which happened to sit close enough to her wood stove to recreate the exact nuisance-trip problem. Rather than moving it, she kept resetting it every time it tripped during normal startup, not connecting it back to her placement decision. It never got disabled, but it trained her to treat every alarm as routine background noise — functionally almost as risky as no detector at all. Swapping to a wall-mounted unit at the correct distance solved it immediately.
For the room with your fireplace or stove, a standalone electrochemical unit, wall-mounted, correctly placed, is my default recommendation. Don’t let outlet location drive placement.
The Decision Sequence, Pulled Together
Step 1: Check your specific local requirement, then set the legal question aside. Missouri has no statewide mandate, but your city or county might. Either way, treat it as a genuine safety recommendation independent of whether it’s technically required.
Step 2: Place it correctly before you worry about anything else. Same room is fine, but 10 to 15 feet from the appliance, never directly above or beside it, away from dead-air corners, vents, and windows.
Step 3: Choose the right type for how you’ll actually maintain it. A standalone, electrochemical, UL 2034-certified unit, wall-mounted, ideally a sealed 10-year battery model.
Step 4: Know your actual replacement date, and know your alarm’s real detection pattern before you ever need it.
The myth worth putting to rest: a headache, or your own nose, would warn you first. This is exactly backwards. CO is genuinely odorless and colorless, and early symptoms aren’t a reliable alarm system either, because CO exposure impairs judgment as one of its actual effects. A mechanical detector isn’t backup to your senses — it’s standing in for senses that were never going to catch this on their own. The second myth: a newer fireplace or stove makes this less necessary. Switching to something newer, or from wood to gas, doesn’t reduce CO risk, it just changes which specific failure point creates it.
The Alarm That Went Off Years Later, Exactly as Planned
A homeowner asked, almost as an aside during a stove install, whether she really needed to worry about all this. We walked through exactly this sequence — confirmed her city had no specific local ordinance beyond the state’s general recommendation, installed her detector in the same room at a proper distance, wall-mounted, standalone electrochemical, sealed 10-year battery. Years later, her alarm went off with the real, distinct detection pattern. Because placement had been correct from day one, she didn’t waste time wondering if it was a nuisance trip. She got her family outside immediately and called from the driveway. It traced to a genuine, developing issue with her stove’s venting — caught early, resolved safely, precisely because every piece of this sequence had been handled correctly years before she ever needed a single one of them.
The Bottom Line
None of these four steps matter individually nearly as much as all of them holding up together, quietly, for years, so that on the one day it actually counts, there’s nothing left to figure out — just the immediate, practiced instinct to get everyone outside. Check your local requirement, place it correctly, choose the right unit, and know its real detection pattern before you ever need it.